Call us
EXPERIENCE
A TRACK RECORD OF
EXCELLENCE
OUR EXPERIENCE
A selection of our projects for clients across diverse industries in Indonesia.
01
REWINDING 5.7 MW BRUSH AC MOTOR
Serviced at our workshop
Incoming inspection and electrical testing
Coil removal
Cleaning of stator core
Rewedges
Coil insertion
Surge testing
Connection
Application of dry air varnish coating (red oxide)
Vacuum Pressure Impregnation (VPI)
Baking
Final testing
02
REWINDING 10 MW IDEAL GENERATOR
Serviced at our workshop
Mobilisation of tools and equipment
Deployment of technicians
Implementation of Lockout Tagout (LOTO) procedures
Preliminary inspection and documentation of existing conditions
Rotor extraction
Mechanical inspection and air cooling system cleaning
Electrical testing post-cleaning
Tan Delta test and offline Partial Discharge (PD) test
Application of dry air varnish coating (red oxide)
03
OVERHAUL 21300 KVA GE GENERATOR
Serviced onsite
Mobilisation of tools, equipment and personnel
Implementation of Lockout Tagout (LOTO) procedures
Preliminary inspection and documentation of existing conditions
Rotor extraction
Mechanical inspection and air cooling system cleaning
Electrical testing post-cleaning
Tan Delta test and offline Partial Discharge (PD) test
Application of dry air varnish coating (red oxide)
Dismantling
Cleaning and baking
Electromagnetic Core Imperfection Detection (ELCID) test
Reassembly and commissioning
04
OVERHAUL 2950 KW TMEIC VERTICAL AC MOTOR
Serviced at our workshop
Incoming inspection and documentation of existing conditions
Preliminary electrical and mechanical testing
Rotor extraction
Dismantling
Mechanical inspection and cleaning
Cleaning and baking
Electrical testing post-cleaning
Replacement of bearings
Rotor balancing
Application of dry air varnish coating (red oxide)
Reassembly
Final testing
05
OVERHAUL 1650 KW ASI ROBICON ARMATURE
Serviced at our workshop
Implementation of Lockout Tagout (LOTO) procedures
Dismantling of generator components and rotor extraction
Coil removal
Rewinding of stator windings
Replacement of Resistance Temperature Detectors (RTDs)
Electrical testing after cleaning
Rotor dynamic balancing test
Replacement of bearings
Application of dry air varnish (red oxide)
Reassembly
06
OVERHAUL 11870 KW ABB GENERATOR
Serviced at our workshop
Mobilisation of personnel
Removal of compartment and heat insulation
Dismantling governor speed control system
Levelling and lifting rotor up
Removal of upper half and lower half labyrinth seals
Sandblasting rotor and diaphragm
Installing rotor
Installing Governor Valve (GV)
Final alignment
Safety device testing
Collection of alignment data
Levelling and rotor lifting
Emergency Stop Valve (ESV) installation
Commissioning
07
REFURBISHMENT 74 KV GRID BLOWER MOTOR
Serviced at our workshop
Record inspection
Dismantling
Coil removal from armature
Rewinding of the armature
Vacuum Pressure Impregnation (VPI) and baking
Rotor balancing
Reassembly
Final testing
08
Refurbishment of 7838 Elmagco Brake Motor
Serviced at our Workshop
Dismantle brake and remove magnet
Electrical and mechanical inspections
Clean magnet pole faces and rotor assembly
Sandblast brake magnets (DE/NDE), bearing housings (DE/NDE), brackets (DE/NDE), rotor drum and main housing/frame
Apply protective coating to all sandblasted areas, excluding magnet pole faces
Repair DE/NDE bearing housings by sleeving
Fit new DE/NDE bearings, grease sleeve seal and seals
Replace corroded bolts as required
Replace heat-shrink lead cable
Supply and install new plug, dowel pin, breather magnet and stopper coupling
Reassemble brake and measure and record air gaps
Painting
09
REWINDING 1250 KW SIEMENS STATOR WHEEL MOTOR
Serviced at our workshop
Coil removal
Electrical testing
Rewedges
Coil insertion
Surge testing
Connection
Application of dry air varnish coating (red oxide)
Performed Vacuum Pressure Impregnation (VPI)
Baking
Final testing
10
OVERHAUL 4100 KVA A VAIN KAICK GENERATOR
Serviced at our workshop
Rotor extraction
Initial electrical testing
Cleaning of stator and rotor windings
Replacement of bearings
Electrical testing post-cleaning
Reinstallation of rotor
Application of dry air varnish (red oxide)
Dismantling
Baking
Balancing
11
REPAIR 21588 KVA HITACHI ROTOR
Serviced at our workshop
Rotor inspection
Preliminary electrical and mechanical testing
Removal of retaining ring
Cleaning of retaining ring
Wedge and coil repair
Wedge installation
Balancing
Final testing
12
OVERHAUL 5000 KW AC INDUCTION MOTOR
Serviced Onsite
Mobilisation of tools, equipment and personnel
Implementation of Lockout Tagout (LOTO) procedures
Preliminary inspection and documentation of existing conditions
Rotor extraction
Dismantling
Mechanical inspection and air cooling system cleaning
Cleaning and baking
Electrical testing post-cleaning
Balancing
Reassembly
Application of dry air varnish coating (red oxide)
Reassembly and commissioning
13
OVERHAUL 6000 KW SHINKO STEAM TURBINE
Serviced onsite
Mobilisation of personnel
Removal of compartment and heat insulation
Dismantling governor speed control system
Levelling and lifting rotor up
Removal of upper half and lower half labyrinth seals
Installing rotor
Installing Governor Valve (GV)
Final alignment
Safety device test
14
Refurbishment General Electric DC Traction Motor
Dismantle
Steam-clean and bake
Electrical tests on windings
Mechanical inspection of motor components
Supply and install new lead cables and cable gland
Sandblast brush holders
Supply and install new spring kit assemblies and carbon brushes
Application of dry air varnish coating (red oxide)
Skim-cut the commutator and perform undercutting
Supply and install new bearings
Dynamic balancing and reassembly
Commissioning
Painting

IN NEED OF a Technical
ASSISTANCE?
Drop us a line and let our team help you find the right solutions to ensure seamless and efficient operations.
MEGA DAYA | EMPOWERING INDUSTRIES














